Naviter Support Forum

I have used Seeyou Mobile together with Flarm so far, works very nice as GPS source. I use an Ipaq 3950.

I now upgraded to Seeyou Mobile 2.6, and to Flarm Version 3 (mandatory). Seeyou Mobile still works properly with Colibri as GPS source, but no more with Flarm. On the terminal screen of Seeyou Mobile I do see data coming in, but with strange symbols.

I have the same problem with SYM 3.0 and Flarm Hw.2 with firmware 4, data out through extension port of flarm

I recive on "Terminal" this log of course  i can see the screen radar  but i don't have gps data.

can we help me
cu
Filosy

Binary date: Feb  7 2008 16:29:24
Binary version: 3.0
Termlog start (y-m-d h:n:s): 2008-07-26 10:52:17
Time zone: 2.00
OS version: 3.0
OS build: 11171
OS Platform: Win32 CE
OS CSD Version:
Processor architecture: Arm
Page size: 4096
Min app addr: 0x10000
Max app addr: 0x7FFFFFFF
Active processors mask: 0x1
Number of processors: 1
Processor type: 2577
Allocation granularity: 65536
Processor level: 4
Processor revision: 0x0009
Memory load: 58%
Total physical memory: 33071104
Available physical memory: 14168064
Total page file: 0
Available page file: 0
Total virtual memory: 33554432
Available virtual memory: 19529728
DEBUG Win version: 0
Mouse present: 1
Screen X: 240
Screen Y: 320
LogPixels X: 96
LogPixels Y: 96
Bits per pixel: 16
Planes: 1
Fonts: 0
Raster caps: 2049
Curve caps: 0
Line caps: 50
Polygon caps: 51
Text caps: 7990
Ports:
  COM1:
  COM2:
Current port settings: COM1:4800,N,8,1,---
------------------------------
$PFLAU,1,1,1,1,0,,0,,*62
$PFLAU,1,1,1,1,0,,0,,*62
$PFLAU,1,1,1,1,0,,0,,*62
$PFLAU,1,1,1,1,0,,0,,*62
$PFLAU,1,1,1,1,0,,0,,*62
$PFLAU,1,1,1,1,0,,0,,*62
$PFLAU,1,1,1,1,0,,0,,*62
$PFLAU,1,1,1,1,0,,0,,*62
$PFLAU,1,1,1,1,0,,0,,*62
$PFLAU,1,1,1,1,0,,0,,*62
9852: $PFLAU,1,1,1,1,0,,0,,*62
0711: $PFLAU,1,1,1,1,0,,0,,*62
6285: $PFLAU,1,1,1,1,0,,0,,*62
6377: $PFLAU,1,1,1,1,0,,0,,*62
6469: $PFLAU,1,1,1,1,0,,0,,*62
6561: $PFLAU,1,1,1,1,0,,0,,*62
6651: $PFLAU,1,1,1,1,0,,0,,*62
6748: $PFLAU,1,1,1,1,0,,0,,*62
7703: $PFLAU,1,1,1,1,0,,0,,*62
8704: $PFLAU,1,1,1,1,0,,0,,*62
9765: $PFLAU,1,1,1,1,0,,0,,*62
0724: $PFLAU,1,1,1,1,0,,0,,*62
1685: $PFLAU,1,1,1,1,0,,0,,*62
2744: $PFLAU,1,1,1,1,0,,0,,*62
3705: $PFLAU,1,1,1,1,0,,0,,*62
4666: $PFLAU,1,1,1,1,0,,0,,*62
5728: $PFLAU,1,1,1,1,0,,0,,*62
6689: $PFLAU,1,1,1,1,0,,0,,*62
7691: $PFLAU,1,1,1,1,0,,0,,*62

The Flarm work good the gps led is green and in flight work fine. I think  possibol  problem in extension port.

cu
Filosy

just one question if you know.

i must get the nmea data from flarm to the extension port or data port ??

 

filosy

Extension port is the right port for sure, because that is where the data flows towards the Flarm Display. SeeYou Mobile simply uses the same data sent to Flarm Display.

I personally use extension port with LX FLARM-SPL-UNIT (see http://www.lxnavigation.si/avionics/accessories.cfm) to have both Display and PDA connected to the same Flarm.

Hmmm.... afaik, the "Original" Flarm with standard configuration only sends warning data ($PFLAU) over the extension port with 4800 baud (look at the log from filosy). Supposable, it's possible to configure this over the Flarm-Tool. In this case, it's necessary to set the baudrate of the extension display, too.

In my opinion, the best way is to use an y-adapter (link) at the main port of the Flarm unit. This solution provides data (by default GPS, pressure, traffic and warning @ 19200 baud) an 12 V for the DC-DC-converter. Alternative, you can use a K6 Anschlussboard or Komplettset

Cheers, Falk